DGHUNST MYJG-100 CO2 Laser Power Review (2026): A Spec-Based Look
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This dghunst myjg 100 co2 laser power review focuses on the MYJG-100, a power supply built for 80W to 120W CO2 laser tubes. It measures 11.2 inches in length and 7.68 inches in width. The unit handles 110V input and supports high-frequency operation for quick response times. You get a compact, lightweight design that separates input and output circuits for safety. This listing details the physical dimensions and compatible tube wattage range. It is a replacement part for engravers and cutters using standard CO2 tubes.
What stands out
- Compatible with 80W-120W CO2 laser tubes
- Compact dimensions of 11.2 x 7.68 x 3.74 inches
- 110V input voltage specification
- Separated input and output circuits for safety
- Quick response speed for high-frequency operation
Who it fits
Good fit for
This power supply suits users replacing a failed unit in an 80W to 120W CO2 laser setup. The compact size fits well in standard engraving machines where space is limited. You will appreciate the separated circuits if you prioritize operator safety during maintenance. The quick response speed helps maintain consistent cutting performance. It is a practical choice for hobbyists or small shops using standard 110V power sources.
Who should skip it
You should look elsewhere if your laser tube requires 220V input, as this model is listed for 110V only. Buyers needing a unit for tubes under 80W or over 120W will find this incompatible. If your machine requires a different form factor than the 11.2-inch length, this will not fit. Those seeking advanced digital controls or app connectivity should check other options, as this unit focuses on basic high-frequency performance.
Verdict: The DGHUNST MYJG-100 is a straightforward, compact power supply for standard 80W-120W CO2 tubes. It offers reliable basic performance for users who need a direct replacement part.
Key specs explained for this unit
Laser Type: CO2
This power supply is designed specifically for carbon dioxide laser tubes. You need this matching type to ensure the electrical output works with your existing laser hardware. Using a mismatched power supply can damage the tube or cause failure. Check your current laser tube type before buying to confirm compatibility with this CO2-specific unit.
Size: MYJG100W (110V)
This label indicates the model version and its voltage requirement. The 110V specification means it requires a standard North American electrical outlet. You must ensure your workshop power matches this rating. Using it with incorrect voltage can damage the internal components. This is a critical safety and compatibility check for any new laser engraver setup.
Width: 7.68 inches
The unit measures 7.68 inches across its shortest horizontal axis. This dimension helps you plan the layout of your engraving station. You need enough clearance around the power supply for ventilation and cable management. Compare this width with other power supplies to see if it fits your existing workspace or cabinet constraints without overcrowding.
Height: 3.74 inches
The vertical measurement is 3.74 inches. This height determines how much vertical space the unit occupies on your desk or inside an enclosure. You should check this against the clearance above your laser tube or other components. A lower profile may allow for tighter integration within a custom-built laser cutter frame or machine housing.
Length: 11.2 inches
The longest dimension of the unit is 11.2 inches. This length affects the depth required in your setup. You need to account for this space when arranging cables and ensuring the unit does not block access to other parts of the machine. Measure your available space carefully to ensure this length fits comfortably within your workstation layout.
Design and build details
The listing describes the MYJG-100 as a compact unit measuring 11.2 inches in length and 7.68 inches in width. The height is listed at 3.74 inches for this specific 110V model. The manufacturer notes a small size and light weight, which suggests the unit is easy to handle during installation. This compact footprint allows it to fit into standard engraving machine frames without requiring extensive structural modifications.
Safety is a key part of the design. The listing states that the input and output circuits are completely separated. This separation helps avoid electric shock risks during operation. The enclosure is well-grounded, which provides an additional layer of protection. The unit can also withstand short periods of open-circuit work, which helps prevent damage to the power supply itself. This feature adds durability for users who may experience occasional operational errors.
Control is handled through simple start and stop functions. The listing emphasizes convenient operation, implying that the interface is straightforward for daily use. The unit is designed for quick response speeds, which supports high-frequency operation. This design choice ensures the laser tube receives power efficiently. The build focuses on practical integration for 80W to 120W CO2 tubes. You can expect a functional, no-frills enclosure that prioritizes electrical integrity and ease of use over aesthetic features.
Setup and everyday use
You install this power supply by connecting it to your existing 80W to 120W CO2 laser tube. The listing notes high compatibility with tubes from multiple manufacturers, which simplifies the matching process. You must ensure your system provides 110V input, as this specific model is rated for that voltage. The unit features a well-grounded enclosure, which is a critical safety step during installation. This grounding helps separate the input and output circuits to prevent electrical shock. You can mount the device in your engraver or cutter frame. The manufacturer highlights a small size and light weight, making physical placement straightforward in most standard machine chassis. You do not need to worry about complex wiring adjustments for basic operation. For daily use, you control the laser start and stop functions easily. The power supply offers a quick response speed, meaning the laser activates and deactivates rapidly when you send a signal. This feature supports high-speed carbon dioxide laser matching, allowing for efficient cutting and engraving tasks. The unit is designed to handle open-circuit conditions for short periods without damage, providing a buffer during normal operation. You can use this component as a replacement part for various CO2 laser markers or cutters. The high-frequency design ensures stable performance during continuous use. You simply connect the control lines to your machine’s interface and power on the 110V source. The system is ready to run once the physical connections are secure. This straightforward setup allows you to focus on your design files rather than troubleshooting hardware compatibility.
Before You Buy This Unit
Before you buy this power supply, verify your laser tube’s wattage falls between 80W and 120W. The listing specifies compatibility with various manufacturers, but you must confirm the electrical requirements match your system. This unit requires 110V input, so ensure your workspace outlet supports this voltage. You also need to check that your engraver’s control board can interface with the start and stop signals described. Proper grounding is essential for safety, as the design separates input and output circuits. Keep the enclosure clean to maintain heat dissipation, as high-frequency operation generates significant energy. If you are replacing a failed unit, compare this size against your current space constraints. The MYJG-100 fits standard CO2 setups, but verify physical dimensions against your existing chassis. This component works alongside your laser tube and controller, so ensure all parts communicate correctly. Regularly inspect the connections for wear, as high-speed operation demands reliable contacts. This guide helps you decide if this specific power supply meets your technical needs without guessing.
Check before you buy
- Confirm your laser tube is between 80W and 120W.
- Verify your system uses 110V input power.
- Check that your control board supports the start/stop signals.
- Ensure you have proper grounding for safety.
- Measure your existing space to fit the 11.2-inch length.
The product at a glance
DGHUNST 100W CO2 Laser Power Supply
Best for: 80W-120W CO2 laser tube replacement
- Laser Type
- CO2
- Dimensions
- 11.2 × 7.68 × 3.74 inches
View on Amazon: DGHUNST 100W CO2 Laser Power Supply Affiliate link
The DGHUNST MYJG-100 is a CO2 laser power supply designed for 80W to 120W laser tubes. It measures 11.2 by 7.68 by 3.74 inches and weighs light enough for convenient operation. The unit features separated input and output circuits for safety and a well-grounded enclosure. You should choose this if you need a replacement part for an existing engraver or cutter that uses high-frequency CO2 tubes.
Pros
- Compatible with 80W-120W laser tubes
- Separated input and output circuits for safety
- Compact dimensions of 11.2 x 7.68 x 3.74 inches
- Quick response speed for high-frequency operation
Cons
- Only supports 110V input voltage
- No mention of digital display or remote control
- Limited to CO2 laser types only
Good fit if
- You need a replacement for an 80W-120W CO2 laser tube
- You require a compact power supply for an existing machine
- You prioritize electrical isolation for safety
Skip if
- You use a fiber laser system
- Your power supply requires 220V input
- You need a laser tube rather than a power supply
Verdict: DGHUNST MYJG-100 CO2 Laser Power Supply is a specialized component for upgrading or repairing 80W to 120W CO2 engravers. It fits users who need a compact, safe replacement for their existing high-frequency laser systems.
Specifications side by side
| Spec | DGHUNST 100W CO2 Laser Power Supply |
|---|---|
| Laser Type | CO2 |
| Dimensions | 11.2 × 7.68 × 3.74 inches |
| Size | MYJG100W (110V) |
Frequently asked questions
Is the DGHUNST MYJG-100 compatible with my 100W CO2 laser tube?
Yes, this power supply is designed for tubes ranging from 80W to 120W. The MYJG-100 unit supports high-frequency operation required by these tubes. You should verify that your specific tube brand is listed as compatible in the product details before purchasing to ensure a proper fit.
What input voltage does this power supply require?
The MYJG-100 requires a 110V input. You must ensure your workspace electrical system provides this specific voltage level. Using an incorrect voltage can damage the unit or the laser tube. This model is not designed for 220V systems without appropriate conversion.
How big is the DGHUNST MYJG-100 power supply?
The unit measures 11.2 inches in length, 7.68 inches in width, and 3.74 inches in height. These compact dimensions allow it to fit into standard engraver chassis. You should measure your existing slot to confirm the physical space is sufficient for installation.
Can I use this as a replacement for a broken power supply?
Yes, it serves as a replacement for 80W to 120W CO2 laser systems. You need to match the wattage range and input voltage of your original unit. This component is intended for users upgrading or repairing existing high-frequency laser engravers.
Does this power supply work with all CO2 laser tubes?
No, it is specific to CO2 tubes within the 80W to 120W range. It does not support other laser types like fiber or diode. You must confirm your tube type is CO2 and falls within the specified wattage limits for proper operation.
Is the DGHUNST MYJG-100 suitable for industrial use?
The listing describes it as a specialized component for upgrading or repairing systems. It is built for high-frequency operation typical in professional engraving. You should verify the duty cycle requirements of your specific industrial application against the manufacturer's specifications.